Printing Methods for the Washington Franklins and Series of 1922 U.S. Stamps

Flat Plate Vs Rotary Vs Offset

Flat Plate
Flat Plate
Rotary Press
Rotary Press
Offset
Offset

There were three methods employed in the printing of the Washington Franklin Head stamps, the flat plate press, the rotary press and the offset press. All designs and denominations of the Washington Franklin stamps were printed using the flat plate method. Only the 1¢, 2¢, 3¢ 4¢, 5¢ and 10¢ stamps were printed using the rotary press method and only the 1¢, 2¢ and 3¢ stamps were printed using the offset method. The Washington Franklin rotary press printings were primarily for coil stamps, although some experimental stamps, as well as the “coil waste” and the rare “sheet rotary” stamps, were printed on the rotary presses. The following information applies to the Washington Franklin stamps, as well as the Series of 1922 stamps and certain commemorative stamps of the era, e.g. the Harding and Edison stamps.

The Template Method for Separating Flat Plate and Rotary Stamps

Width Template – the top half of the image above, is placed over the subject stamp. By looking at the right margin it is clear the subject is wider than the template. The subject stamp is therefore rotary.

Height Template – the right half of the image above, is placed over the subject stamp. By looking at the bottom margin it is clear the subject is taller than the template. The subject stamp is therefore rotary.

Examples of Templates
Examples of Templates

An easy method to sort flat plate and rotary press stamps in quantity is to cut a damaged common flat plate stamp in half and use it as a template. Perf 12 Washington Franklins make good examples since they will always be flat plate. You will need two templates, one cut horizontally and one cut vertically, since the rotary press stamps can be longer in either direction, or you can make a single template with four cut corners, as in the picture above. Note that you can use any flat plate stamp of the same size as a template, it does not have to be of the same denomination or color, only the size matters. You might also want to make a rotary press template if you have a few beat up rotary press coils.

Distinguishing Offset Stamps

The key to separating offset from rotary and flat plate is to realize that the offset stamps were not engraved. This means that the ink lies flat on the paper of the offset stamp. If you hold the stamp at a very sharp angle to a light source, the color on the stamp will almost disappear. This is just the opposite for the engraved stamps. In fact, one way to tell if a U.S. stamp is genuine and not a reproduction, is to perform this test. All engraved U.S. stamps will clearly show raised ink when held at a sharp angle to light. The offset method of printing also resulted in some very poor quality stamps. In many cases a stamp can be identified as offset just by looking at it, the color and printing quality are that poor.

Sometimes visual inspection is not enough and another method of determination must be made. Since the offset method does not employ engraving, the stamp feels flat. Some collectors can feel the lack of engraving by merely running their fingers across the stamp. A semi-soft nib may be ran gently over the surface, particularly in the area of several parallel lines. This must be done very carefully in order to not scratch the ink from the stamps surface or damage the surface of the stamp in any way. Another favorite method is to use a piece of aluminum foil, or other thin foil, the thinner the better. Place the foil over the stamp in question and rub your finger very gently over the foil. The frame of the oval portrait and other details will show on the foil on flat plate and rotary stamps, but will not show on the offset stamps. Again, care must be taken not to damage the stamp by rubbing too hard. Gentle pressure should bring out the features on the engraved stamp. Practice these techniques on some of the more common varieties and you will soon be an expert at separating engraved and offset stamps.

Design Types on the offset 2¢ and offset 3¢ Washington Franklin Stamps.

Bibliography and suggested further reading:

Printing Postage Stamps by Line Engraving, by James H. Baxter. Printed by the American Philatelic Society
The Development of the Rotary Press Printing, by Max G. Johl – Stamp Specialist Vol. 1: 1, Published 1939
United States Stamps 1922-1926, by Gary Griffith. Published by Linn’s Stamp News.
Fundamentals of Philately, by L. N. and M. Williams. Published by the American Philatelic Society

Sidebar